เทเบิ้ลฟีดเดอร์ สามารถเชื่อต่อจากไซโลและฮอปเปอร์ได้ และไม่จำเป็นต้องปรับเปลี่ยนขนาดของทางออก We make not only the rotary valve, but also other canned products. For example, they are below, Screw conveyor and Table feeder ◆Screw Conveyor Aishin Japan have many experiences about the screw conveyor. We can design more than 5m long type, the model that has big rotor and so on. Off course, we will make the food grade type if you request. ◆Table Feeder Table feeder is the product for discharging material. It is different from the rotary valve as below. Table feeder can be connected from silo or hopper. At that time, you don’t need to modify them such as changing outlet size. Because Table feeder […]
We have a lineup of piping connection. The EURAC Coupling, you can use it only when you connect the pipes. Coupling Catalog Data (PDF) As above photo, you don’t arrange the gasket, bolts and nuts due to piping connection. Additionally, its cost is cheaper than flange connecting. (*Depending on the specification) If you request any more information, please contact us!
We would like to take this opportunity to thank you for your continued support of our company. PROPACK ASIA is postponed to next year. When new schedule is announced, we will inform you. That’s quite unfortunate, but we will update our items. We would like to announce the participation in the exhibition.
The AIT’s rotary valve has options to support the customer`s system and material. *Please note these options don`t guarantee the described effects. １：Safety ◇Limit switch on the door（Sanitary type） When the door is opened, the limit switch is activated to stop the rotor. ２：Material measure ◆Staffing BOX Purge Nozzle This is for remove the inside adhesion of materials. (Between stuffing BOX and rotor) ◇Rotor blow nozzle This for remove the material in the rotor. ◆Inner surface buffing（Powder contact part made of stainless steel） The surface smoothly and reduces the adhesion of raw materials. #300 and #400, you can choose 2 types. ◇Anti-trap chute（Measures against material biting） The […]
What is the rotary valve ? -4(Sanitary Type Variation) The sanitary rotary valve we make some kinds. ◆Variation We propose 3 different types to meet your requirements. 1. One side shaft seal type Our standard rotary valve is one side shaft seal type.Normally, rotary valves have shaft seals and bearings on both sides, but this type does not have them on the open / close door side.As a result, the number of parts is reduced, but the clearance is properly maintained through accurate design and manufacturing. 2. Both side shaft seal type In case, If the conditions of the installation site are severe、it also installed a shaft seal and bearing […]
We would like you to know the rotary valve better. Please look at below figure. ◆Introduction of each Rotary valve We would like to introduce Sanitary Rotary Valve (SMC). The Sanitary type has a door opening/closing structure that allows easy access to the inside. We recommend it if you often inspect and clean RV inside. 1.Standard Sanitary Rotary Valve. The Standard Sanitary Rotary valve can be opened the door and separated the rotor. ※Another Sanitary Type (Made by other company) *Rotor and door are set parts. If you clean inside, pull out them along the slide rails. The Comparison chart (standard type and Slide rails type) Some customer request […]
We would like to take this opportunity to thank you for your continued support of our company. We will inform you again because the PROPACK schedule has been changed. ※The schedule is expected to change in the future. Please keep this in mind. We will be exhibiting our booth at PROPAK ASIA in September. We hope that you will take this opportunity to visit us and stop by our booth. Schedule: 15 to 18.9.2021 Time：10:00-18:00 Address: Bangkok International Trade and Exhibition Centre (BITEC) Booth No. AJ36 Equipment to be exhibited: Sanitary Rotary Valve, Ball diverter Valve, ERAC coupling. The ball diverter valve and EURAC coupling will be displayed on a […]
We would like to take this opportunity to thank you for your continued support of our company. We will be exhibiting our booth at PROPAK ASIA in June. We hope that you will take this opportunity to visit us and stop by our booth. Schedule: 16 (Wed) ～ 19 (Sat) .6.2021 Time：10:00-18:00 Address: Bangkok International Trade and Exhibition Centre (BITEC) Booth No. AJ36 Equipment to be exhibited: Sanitary Rotary Valve, Ball diverter Valve, ERAC coupling. The ball diverter valve and EURAC coupling will be displayed on a stand that shows an image of the connection.
What is the rotary valve ? -2 (Basic Type) We would like you to know the rotary valve better.Please look at below figure. ◆Types of Rotary valve Rotary valve has some types, depending on how you use them. This figure is the reference for choice the type of Rotary Valve.We consider details of powder, installation location and environment, and purposes. ◆Introduction of each Rotary valve We introduce Basic Rotary Valve. ◆Basic RV If you don`t need the spec that is available to clean and check inside easily,We recommend Basic type RV.Both side covers (Stuffing BOX) are fixed by bolts and nuts.(Right)This model has 2 types of structures. 1: Basic RV […]